LG Washer Stuck on Spin Cycle? 7 Ways To Easily Fix It

There is no doubt that LG washers are some of the most popular high-quality machines in the world, for they are efficient and quiet.

However, when it comes to the spin cycle, they can be tough to deal with. The LG washer might be stuck on the spin cycle without draining and rinsing. 

Usually, LG washers are stuck on spinning when the water isn’t draining, caused by broken sensors or malfunctioning parts. 

If your washer is stuck on a repetitive spin cycle, your clothes will get soaking wet without drying. The machine will also use more water, which is bad for the machine’s environment and your pocket. 

Have you tried a hard reset to fix the problem with no result? You’re in the right place. Today we’ll tackle the LG washer stuck on spin cycle issue to determine the most common causes for the problem and find a quick fix.

Why is your LG Washer Stuck on Spin Cycle?

You always have to treat your LG washer with care since failing to do so will result in broken sensors and clogs. 

To prevent the never-ending spin cycle, you need to use the washer cleaning tablets to remove the chunk that builds up around different parts of your washer. 

Besides, remember to check your clothes every wash cycle. If something is missing, it is most likely, stuck in one of the hoses. It would be best to get it right away to prevent more severe issues. 

It is also vital that you have to reset your LG washer at least once per month. Just turn off the machine, unplug it, and plug it back in. It helps to keep your washer from becoming overworked.

Still, things can go out of hand no matter how hard you try to maintain your LG washer. So you have to be prepared. 

Let’s list the most common reasons why LG washer is stuck on the spin cycle to know what to look for.

1. Faulty Timer

A timer controls most functions of your washer, including cycles. So if the LG washer is stuck on the spin cycle, faulty time could be responsible for that. The washer will keep trying to spin wet clothes, but the timer won’t move on. 

It is a frustrating but common experience when it comes to spinning issues.

2. Unlocked lid

Some front-load washers are equipped with the door interlock attribute. You must seal the lock before the wash cycle. However, if the door is stuck in the locked position and you can’t open it, there is no need to panic. 

A faulty door interlock switch usually causes this. Besides, the washer won’t be able to move to the next cycle because of it and might be stuck on spinning.

3. Overload

Another reason why the LG washer might be stuck on the spin cycle is you overload the washing machine. The machine will take too long to complete the spin cycle when clothes are over 80% of your washer’s capacity.

4. Worn drive belt

The drive belt is a part responsible for rotating the drum during the wash cycle. It is located between the motor and the drum. It also helps to keep the drum in place during the spin cycle.

A worn-out drive belt reduces the spin speed and keeps the cycle on repeat. 

5. Faulty sensors

Since LG washers primarily run on timers, they have few sensors. Correspondingly, a faulty sensor can be a culprit. 

The washer’s sensor is supposed to register if the water is drained. If it fails, it will continue to tell the washer to spin forever, and your LG washer will be stuck on the spin cycle. 

If there is no water in the machine, but it stays on the spin cycle, it’s a sign that something is wrong with one of the sensors

6. Old filter system

Your washer’s filter can become corroded or clogged and show all kinds of problems over time. Because of age, the filter and filter cover starts to prevent the water from draining correctly. 

If your washer makes an unusual sound like humming, the drain filter is most likely blocked.

As a result, the water overflows inside the washing machine and continues to spin for longer than it should.

Unfortunately, clogged, broken, or old filters are inevitable. The least you can do is clean it monthly to avoid issues with the spin cycle.

7. Clogged drain hose

It shouldn’t come as a surprise that some small pieces of clothing can clog the hose of your LG washing machine. Underwear, socks, or other small garments can clog the hose, and the washer won’t be able to drain water. 

Moreover, it can grow mold and mildew and cause foul odors.

How to fix an LG Washer Stuck on Spin Cycle?

Sometimes, the LG washer might be stuck on spinning just because something is blocking the door from closing properly. Or it could be the clogged drain hose or dirty sensor.

Regardless of the reason, you should see the issue immediately once it appears to avoid any further damage.

Here’s what you need to do.

1. Reset LG washer 

The first thing to do when the LG washer is stuck on the spin cycle is to reset your washer. Before you take any action, we recommend consulting your user manual. There could be some specific way of resetting your model of the washer.

If you can’t find the user manual, unplug your washer from the power outlet and wait for at least five minutes so the electric current can discharge. Then turn the machine back on.

If it doesn’t work, try a hard reset that disconnects the washer from the power source. Then open and close the lid six times for 12 seconds. Make sure to adhere to the timing. 

Finally, run the spin cycle and check if the issues persist. If it does, then you should check other components.

2. Replace the timer

If the reset doesn’t help, the second thing to check is the timer. Timer gets defective because of the short-circuited contacts most of the time. 

Once you unplug the machine and switch off the water supply, unfasten the control panel. Then unscrew the timer from the board. Remove it slowly, together with the wiring harness clip.

Test the timer for continuity with the multimeter and replace it if there are no sights on continuity.

3. Check the lid

Check the door and door switch for damage if the LG washer is stuck on the spin cycle and can’t move to the next cycle. If there is no damage, try resetting the machine by unplugging it from the power outlet and plugging it back in.

Also, check if anything is blocking the washer from spinning. If there is nothing, check the door lock switch. It might be defective and need replacement.

4. Avoid overloading

The LG washer will stop working properly if you overload it continuously. And it is not only regarding the spinning. 

There are a few things you can do to avoid the overload. First, ensure an even distribution of your laundry load in the machine. Pack only a little since it forces your washer to work harder.

Besides, you must select the correct load size water level. If there is too much water, it won’t only take longer for clothes to wash but will cause an overload.

Also, ensure you use the right cycle for your type of laundry. Heavy loads cause the washer to become overloaded.

5. Clean the drain filter

If the drain filter is blocked with lint and debris is the reason for the issue, you should clean it to avoid any more complex consequences. 

Start unplugging the washer from the power source to clean the drain filter. Ensure the plug is away from your work area so it doesn’t get wet.

Place a small bucker or dry towel on the floor close to the washing machine to collect water that might pour once you open the filter. 

Locate the filter in the right corner in the front of your machine (if you use the LG front load washer). Check the user manual if you can’t locate it. Pull off the filter cover with the screwdriver and take the filter out carefully. 

Remove the filter scream and soak it in hot water for about 10 minutes to release the debris and lint. While the steam is soaking, clean the filter holder.

Finally, rinse the screen of dirt, place it back inside the LG washer, and secure it tightly.

6. Change broken sensor

When the issue is the broken or dirty sensor switch, your washer will flash the PE error. To check if it is broken, consult your user manual and locate the sensor in your machine. 

If the sensor is dirty, you must remove and clean it. But if you place it back in the washer, run a test spin cycle, and discover that the washer is still stuck on spinning, replace the sensor.

7. Replace the drive belt

It would help if you first unplugged the machine from the power socket to replace a defective drive belt. Besides, you need to locate the water inlet valves, lock them and ensure to disconnect the water plug.

Then unscrew the access panel from the front of the machine. The belt is usually close to the motor or drum. You should unfasten the cover of the belt. But note that some LG washer models don’t have the belt cover.

The next step is disconnecting the old belt from the drum’s pulley and replacing it with a new one. A new belt must fit your model so it can function properly.

Attach the new drive belt to the drum pulley with the zip ties and hook the other side of the belt on the pulley. Rotate the pulley to access the tie and cut it with scissors.

Finally, fasten the belt cover back or ignore this step if you have no cover. Screw in the access panel, connect the water inlet valve, and power to the washer.

The stuck spin cycle issue should be fixed.

Related Article:  LG

4.7/5 - (10 votes)
DMCA.com Protection Status
error: Content is protected !!